Acoustic Guitar Construction

Posted: **Mon Nov 18, 2019 12:28 pm**

Thanks Herman. Here’s the top glued to the rims and ready for the back.

: 1FE3677B-7E90-4306-9E47-16ECDAC67B6C.jpeg (200.33 KiB) Viewed 1088 times

John

Posted: **Fri Nov 22, 2019 2:34 pm**

gorgeous work! So that pickup also has an internal microphone? Is there a way to mix between the under the saddle and the microphone?

Posted: **Fri Nov 22, 2019 2:59 pm**

Thanks John. No that is a volume wheel. I didn’t want to risk getting finish on so it’s just taped out of the way.

John

Posted: **Thu Dec 05, 2019 11:24 am**

Box is about done. Just some finish sanding.

: Ebony binding.; EECF4762-BA88-4DF5-A28E-8A280E17A49D.jpeg (167.42 KiB) Viewed 1070 times

: Channel after the Teflon strip has been removed.; E4EEC1E2-D69A-4565-9D99-8EF44D1CA834.jpeg (237.64 KiB) Viewed 1070 times

: Installing the purfling segments.; B4D4B947-0579-4248-93A5-4F91E08A4338.jpeg (310.56 KiB) Viewed 1070 times

: E0D7656F-4EE4-4015-9EDB-9811E57D9DE6.jpeg (239.49 KiB) Viewed 1070 times

John

Posted: **Thu Dec 05, 2019 2:19 pm**

That purfling is way cool! I love the look.

Posted: **Thu Jan 16, 2020 1:46 pm**

Thanks John.

Slow progress with the holidays, but I have done a bit. The neck attachment is similar to the Gore/Gilet bolt on. This differs in a couple of ways. The heel profile has to be at its final shape and sanded to a nearly finish state. The tenon is tapered from just underneath the top bolt hole to the bottom of the tenon. And since the fingerboard extension is not bolted down, but is free floating, it too has a slight taper to the underside.

: 3CB4FF86-4DA0-427A-B364-46346FC6A7F0.jpeg (269.38 KiB) Viewed 1018 times

: 08C068C7-AD7E-43F8-8B88-98340040207A.jpeg (268.02 KiB) Viewed 1018 times

Then I bolt it up and check for angle and center. Then I’ll use a new scalpel blade to scribe the heel outline on the body.

: 11881BE7-1B35-488B-BF51-BA4377622039.jpeg (262.21 KiB) Viewed 1018 times

: 3603FAF0-481F-4EC8-B909-32D90615B06B.jpeg (302.66 KiB) Viewed 1018 times

Then I oh so carefully rout out the heel pocket, finishing with a sharp chisel. I then deepen the neck pocket slightly from just below the top bolt hole to the bottom of the heel. This allows for movement.

: 14E777E3-7BBA-4805-9CFE-BA2FE7E45306.jpeg (282.36 KiB) Viewed 1018 times

: D61E37CA-C677-4303-83D4-ED7C0D1BD038.jpeg (313.09 KiB) Viewed 1018 times

A final fitting and I can finish shape the neck.

: 0EFED431-13C6-4F39-AC8A-94D0C9903E4E.jpeg (308.28 KiB) Viewed 1018 times

Posted: **Thu Jan 16, 2020 2:17 pm**

Wow, That work looks really good. I like the neck design. Look forward to seeing this guitar complete.

Acoustic Guitar Construction

Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M

Re: Cocobolo O’M