Construction Log for KMG J45-Style Dreadnought

[dave d]

Introduced by Gibson in 1942 as one of the dreadnought acoustics to compete with Martin's 'D' line, and often referred to as "The Workhorse."

Peruvian Walnut back and sides, Sitka spruce top, abalone rosette, cherry/walnut laminated neck.

Setting up the mold with the template.

DBD_7370.JPG (114.92 KiB) Viewed 7528 times

Make sure the template is centered.

DBD_7372.JPG (70.39 KiB) Viewed 7528 times

Post is placed near the innermost waist curve.

DBD_7375.JPG (81.8 KiB) Viewed 7528 times

Sides are placed in the mold and marked at the centre line for cutting.

DBD_7381.JPG (80.21 KiB) Viewed 7528 times

I use my bench-hook and a japanese pull-saw to cut the side at the marked location.

DBD_7384.JPG (76.97 KiB) Viewed 7528 times

Sides placed back in the mold to check for fit.

DBD_7386.JPG (63.39 KiB) Viewed 7528 times

Drill a couple of holes for the nails to hold the sides in place when you are gluing.

DBD_7393.JPG (71.78 KiB) Viewed 7528 times

Neck block being clamped to the sides.

DBD_7397.JPG (76.79 KiB) Viewed 7528 times

A little bit of glue squeeze-out is a good sign.

DBD_7399.JPG (77.48 KiB) Viewed 7528 times

Neck and tail blocks glued to the sides.

DBD_7404.JPG (57.63 KiB) Viewed 7528 times

[dave d]

On to the next steps: kerfing and profiling.

After wetting and pre-bending the kerfing, it is glued to the top side of the rim.

DBD_7410.JPG (86.38 KiB) Viewed 7521 times

The top edge is lightly sanded with a sandpaper-covered piece of stock so the edge has a flat plane.

DBD_7411.JPG (85.98 KiB) Viewed 7521 times

The rim and neck/tail block are all in a flat plane.

DBD_7419.JPG (32.42 KiB) Viewed 7521 times

The sides are flipped over so the top is facing down, and the kerfing is glued to the back side.

DBD_7427.JPG (71.97 KiB) Viewed 7521 times

Kerfing shown on both the top and back sides.

DBD_7430.JPG (90.66 KiB) Viewed 7521 times

Cedar reinforcing pieces are glued to the sides.

DBD_7435.JPG (74.89 KiB) Viewed 7521 times

Profiling the top: Take a measurement using feeler gauges at the front part of the neck block.

DBD_7443.JPG (73.62 KiB) Viewed 7521 times

Transfer the measurement to the collar on the spindle. This is the distance the sanding bar will drop to when the neck angle is properly profiled.

DBD_7444.JPG (59.78 KiB) Viewed 7521 times

Photo showing neck block mid-way through sanding. Pencil marks gauge your progress.

DBD_7446.JPG (56.11 KiB) Viewed 7521 times

Side view of the mold, showing the angle that the neck block is sanded to.

DBD_7454.JPG (58.98 KiB) Viewed 7521 times

[dave d]

Profiling the back, and getting the abalone strips into the rosette channel.

now to put the 15' radius on the back edge.

DBD_7460.JPG (62.24 KiB) Viewed 7519 times

I like to check the fit of the back on the rim, just to get an early look even though the bracing isn't on yet.

DBD_7463.JPG (54.3 KiB) Viewed 7519 times

The sitka spruce top.

DBD_7468.JPG (48.73 KiB) Viewed 7519 times

Trial fit of the abalone strips and purfling.

DBD_7476.JPG (55.65 KiB) Viewed 7519 times

Sealing the rosette channel with lacquer to prevent the CA glue from seeping into the spruce and turning it a weird color.

DBD_7477.JPG (62.7 KiB) Viewed 7519 times

Everything back in place and CA wicked in.

DBD_7480.JPG (54.03 KiB) Viewed 7519 times

Scraping to level it out with the top.

DBD_7484.JPG (83.28 KiB) Viewed 7519 times

Scrape scrape scrape. Be careful to not tear the spruce when going across the grain.

DBD_7486.JPG (75.41 KiB) Viewed 7519 times

Rosette done for now.

DBD_7500.JPG (110.57 KiB) Viewed 7519 times

[Dave Bagwill]

Thanks for posting Dave, I never get tired of watching a building log. The macro tips were good also.

[ken cierp]

Awesome!!! As usual. Very enjoyable to follow -- Thank you

[Jackspt28]

Beautiful work!! Like the bench hook for trimming the sides, will have to use that idea! Thanks for posting. Jack.

[Kevin in California]

Coming along very well in deed. You have to love abalone rosettes!

Kevin