Zebrawood Venetian Cutaway

Show us how your current project is progressing
Post Reply
Kevin in California
Posts: 2824
Joined: Mon Dec 19, 2011 4:19 pm

Re: Zebrawood Venetian Cutaway

Post by Kevin in California » Thu Jun 30, 2016 11:44 am

Looks great, but makes me dizzy :)
Top
John J
Posts: 359
Joined: Fri Nov 14, 2014 4:30 pm
Location: Saint Paul, Minnesota

Re: Zebrawood Venetian Cutaway

Post by John J » Sun Jul 10, 2016 9:30 am

Time for carving.
Attachments
image.jpeg
image.jpeg (120.26 KiB) Viewed 1177 times
image.jpeg
image.jpeg (68.07 KiB) Viewed 1177 times
JJ
Learning every day. And having fun doing it.
Top
Kevin in California
Posts: 2824
Joined: Mon Dec 19, 2011 4:19 pm

Re: Zebrawood Venetian Cutaway

Post by Kevin in California » Mon Jul 11, 2016 7:46 pm

That is the fun part!
Top
John J
Posts: 359
Joined: Fri Nov 14, 2014 4:30 pm
Location: Saint Paul, Minnesota

Re: Zebrawood Venetian Cutaway

Post by John J » Tue Jul 19, 2016 9:15 pm

Box closed and trimmed and sanded square. Installed tail wedge and corner trim at neck prior to cutting mortise and binding rebates.
Attachments
image.jpeg
image.jpeg (84 KiB) Viewed 1149 times
image.jpeg
image.jpeg (126.02 KiB) Viewed 1149 times
image.jpeg
image.jpeg (121.42 KiB) Viewed 1149 times
JJ
Learning every day. And having fun doing it.
Top
John J
Posts: 359
Joined: Fri Nov 14, 2014 4:30 pm
Location: Saint Paul, Minnesota

Re: Zebrawood Venetian Cutaway

Post by John J » Wed Jul 27, 2016 9:01 am

Moving a little slow on this one. Too hot/humid to get much done. I've finally finished installing and leveling the bindings and top purfling. I had pre bent the bindings and hand bent the purfling except the cutaway purfling section. Saved that for last. Installed at the same time with titebond. The last section was bent with the aid of super soft and water and a combo of my bending pipe and a heat gun. I'd get it quite warm and then push it in the rebate on the guitar body and hold while it cooled. Quite a few repeats of this step and it finally got close enough to glue in. Sanded level and I'll only have some very minor gaps to fill.
Attachments
image.jpeg
image.jpeg (111.14 KiB) Viewed 1132 times
image.jpeg
image.jpeg (111.02 KiB) Viewed 1132 times
image.jpeg
image.jpeg (107.45 KiB) Viewed 1132 times
JJ
Learning every day. And having fun doing it.
Top
Herman
Posts: 1711
Joined: Sun Dec 30, 2012 1:20 pm
Location: Arnhem area, the Netherlands
Contact:
Contact Herman

Re: Zebrawood Venetian Cutaway

Post by Herman » Wed Jul 27, 2016 11:59 am

Yo JJ, That is a lot of detail, but looking good though. Sharp work!
Herman
Top
Kevin in California
Posts: 2824
Joined: Mon Dec 19, 2011 4:19 pm

Re: Zebrawood Venetian Cutaway

Post by Kevin in California » Wed Jul 27, 2016 12:11 pm

Looking great John.
Top
Post Reply

Return to “Construction logs”