Great place mat, good for wood, bad for finish

Ideas for (DIY) shop made tools -- save money and add to the enjoyment
Herman
Posts: 1685
Joined: Sun Dec 30, 2012 1:20 pm
Location: Arnhem area, the Netherlands
Contact:

Great place mat, good for wood, bad for finish

Post by Herman » Sat Jun 28, 2014 11:56 am

In an officestore I found this anti-slipmat for 1 euro.
It's a open rubber covered fabric 13" wide. Very soft feel.
It works great as a surface to put the guitar on and not scratching the plates while working on the other side.
Currently it is used on a cedar topped guitar and since start using it, I have no dents or scratch anymore.
I love this one. I guess in the US you can find something similar.

Image

Image
Last edited by Herman on Thu Jul 03, 2014 1:39 pm, edited 1 time in total.

John Link
Posts: 800
Joined: Tue Nov 27, 2012 8:01 pm
Location: Kalamazoo, MI

Re: Cheap but great place mat

Post by John Link » Sat Jun 28, 2014 12:04 pm

Looks useful.
John

Lonnie B
Posts: 542
Joined: Thu Sep 05, 2013 7:42 pm

Re: Cheap but great place mat

Post by Lonnie B » Sat Jun 28, 2014 11:09 pm

Herman;I've seen that stuff somewhere. My wife bought a yoga mat I think will work out as well. I've pretty much finished the little Ukelele I made for the little girl. I put the first coat of finish on it (Tru-oil) from what I understand EIR is notoriously slow drying. But think I'll use her yoga mat.

Ray Ussery
Posts: 662
Joined: Wed Dec 21, 2011 12:51 am

Re: Cheap but great place mat

Post by Ray Ussery » Sun Jun 29, 2014 9:45 am

You can buy it here in most RV supply's, Wal-mart and even $ stores...bare wood is fine...just be aware that it will absolutely RUIN a lacquer finish, even if it is long set...
I laid a Tele body that I had finished 5 years ago on the stuff to keep it in place while I wired it and installed the neck etc.
It imprinted the exact pattern on the back...I couldn't rub it out...none of the finishing compounds I've used including 3M...I tried using the finer grits of Micro Mesh up to and including 12000...to no avail...I decided to experiment because I had nothing to loose, so I sanded the back down and tried to clear coat it again...nope....still there... I had to take it apart, sand it all down to bare wood and start over...I was not happy!
Got a guitar your going to refin? Try it...you'll see what I mean....don't know what it will do with other finishes but I'd sure do a test before I used it.....02

Lonnie B
Posts: 542
Joined: Thu Sep 05, 2013 7:42 pm

Re: Cheap but great place mat

Post by Lonnie B » Sun Jun 29, 2014 9:50 am

Wow Ray; I've heard enough. I've been useing a thick Terry cloth Bath Towel. It's been working fine. Think I'll stick with that.

John Parchem
Posts: 2749
Joined: Fri Dec 23, 2011 8:33 pm
Location: Seattle
Contact:

Re: Cheap but great place mat

Post by John Parchem » Sun Jun 29, 2014 10:21 am

I had a black mat that looked like that one and it ruined a lacquer finish. I am a bit gun shy now. The stuff I had was from a marine store.

Herman
Posts: 1685
Joined: Sun Dec 30, 2012 1:20 pm
Location: Arnhem area, the Netherlands
Contact:

Re: Cheap but great place mat

Post by Herman » Sun Jun 29, 2014 10:44 am

Yeah Ray, good tip to be careful with it.

Post Reply