Ladder-braced parlor guitar

Show us how your current project is progressing
Post Reply
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: Ladder-braced parlor guitar

Post by Dave Bagwill » Tue Sep 24, 2013 8:00 pm

Today I got the back and top glued and thicknessed. Also have the sides thicknessed, laminated, and in the vacuum bag. Ignore the coloration *(&%*&(*& camera.
Attachments
a useless pic - the mega mold you all recognize, I used it to create the correct side profile. The joined back is to the right and blurry. Off to the left the top is being joined. I used Ken Cierp's idea for joining the back, and used the tape method for the top.
a useless pic - the mega mold you all recognize, I used it to create the correct side profile. The joined back is to the right and blurry. Off to the left the top is being joined. I used Ken Cierp's idea for joining the back, and used the tape method for the top.
DSC00930.JPG (140.16 KiB) Viewed 2451 times
the lamination - .045" sapele on the bottom - this is the outside layer - then .025 maple in the center, and .025 sapele inside. Profiled first.
the lamination - .045" sapele on the bottom - this is the outside layer - then .025 maple in the center, and .025 sapele inside. Profiled first.
DSC00931.JPG (145.6 KiB) Viewed 2451 times
in the bag for a few hours.
in the bag for a few hours.
DSC00932.JPG (145.04 KiB) Viewed 2451 times
-Under permanent construction
Top
ken cierp
Posts: 3924
Joined: Tue Dec 13, 2011 11:23 pm

Re: Ladder-braced parlor guitar

Post by ken cierp » Wed Sep 25, 2013 11:14 am

What kind of adhesive for the laminations?
Top
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: Ladder-braced parlor guitar

Post by Dave Bagwill » Wed Sep 25, 2013 11:19 am

West systems epoxy
-Under permanent construction
Top
ken cierp
Posts: 3924
Joined: Tue Dec 13, 2011 11:23 pm

Re: Ladder-braced parlor guitar

Post by ken cierp » Wed Sep 25, 2013 12:32 pm

What keeps the sides/epoxy from sticking to the vac bag?
Top
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: Ladder-braced parlor guitar

Post by Dave Bagwill » Wed Sep 25, 2013 12:48 pm

I roll that epoxy on and into the laminate with some vigor, there is no squeeze-out to speak of, not a problem.


ps - I'll try to remember to do a very short vid next time I use the epoxy, you'll see what I mean. It's a technique I learned from Brian Burns.
-Under permanent construction
Top
Tim Benware
Posts: 1489
Joined: Thu Dec 22, 2011 1:22 pm
Location: Asheboro, NC

Re: Ladder-braced parlor guitar

Post by Tim Benware » Wed Sep 25, 2013 2:45 pm

Do you use the same West epoxy for pore filling?
I've "Ben-Had" again!
Tim Benware
Creedmoor, NC
Top
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: Ladder-braced parlor guitar

Post by Dave Bagwill » Wed Sep 25, 2013 2:47 pm

I don't. I've actually talked to a couple of folks that say they do, but it just is not designed for that purpose.

Dang, I should try it on some scrap just to prove it to myself.
-Under permanent construction
Top
Post Reply

Return to “Construction logs”