My KMG OM-28V Project

Show us how your current project is progressing
Post Reply
Dennis in Anola
Posts: 224
Joined: Tue Mar 27, 2012 10:45 am
Location: Anola Manitoba

Re: My KMG OM-28V Project

Post by Dennis in Anola » Wed Sep 18, 2013 1:15 pm

Ok, after taking some time off to build a deck for my wife (happy wife = happy life), some fishing and a few social obligations I'm back working on my guitar. I got the rosette done today. I used a scraper this time to avoid the black wood contamination problem I encountered with my first guitar.
Attachments
OM.Rosette.jpg
OM.Rosette.jpg (281.22 KiB) Viewed 1253 times
Just when you think you're getting ahead in the rat race, the rats get faster.
Top
Tim Benware
Posts: 1489
Joined: Thu Dec 22, 2011 1:22 pm
Location: Asheboro, NC

Re: My KMG OM-28V Project

Post by Tim Benware » Wed Sep 18, 2013 3:38 pm

Nice. I like that design.
I've "Ben-Had" again!
Tim Benware
Creedmoor, NC
Top
Dennis in Anola
Posts: 224
Joined: Tue Mar 27, 2012 10:45 am
Location: Anola Manitoba

Re: My KMG OM-28V Project

Post by Dennis in Anola » Wed Sep 18, 2013 8:45 pm

Tonight I got the bridge plate and X-braces glued up. This shot shows a dry run before following Ken's instruction. I amazed myself with very tight center brace notches. They turned out better than I hoped for.
Attachments
OM28V..XBrace.jpg
OM28V..XBrace.jpg (220.48 KiB) Viewed 1240 times
Just when you think you're getting ahead in the rat race, the rats get faster.
Top
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: My KMG OM-28V Project

Post by Dave Bagwill » Wed Sep 18, 2013 9:28 pm

Looking good!
-Under permanent construction
Top
Dennis in Anola
Posts: 224
Joined: Tue Mar 27, 2012 10:45 am
Location: Anola Manitoba

Re: My KMG OM-28V Project

Post by Dennis in Anola » Sat Sep 21, 2013 12:16 pm

Top ready to fit to the rim:
Attachments
OM top braces.jpg
OM top braces.jpg (290.56 KiB) Viewed 503 times
Just when you think you're getting ahead in the rat race, the rats get faster.
Top
Dennis in Anola
Posts: 224
Joined: Tue Mar 27, 2012 10:45 am
Location: Anola Manitoba

Re: My KMG OM-28V Project

Post by Dennis in Anola » Sun Sep 22, 2013 11:43 am

Inside Shot. Note, this top is lightly braced with 1/4" bracing.
The back gets glued on today. Then I'll see if I can bend the Herringbone binding.
Attachments
OM Inside Shot.jpg
OM Inside Shot.jpg (299.4 KiB) Viewed 493 times
Just when you think you're getting ahead in the rat race, the rats get faster.
Top
Dave Bagwill
Posts: 5951
Joined: Tue Dec 13, 2011 7:44 pm

Re: My KMG OM-28V Project

Post by Dave Bagwill » Sun Sep 22, 2013 1:08 pm

Nice and clean work. I use 1/4" braces almost exclusively now.
-Under permanent construction
Top
Post Reply

Return to “Construction logs”